| Software |
– Cisco Unified Wireless Network Software Release 8.10.x or later |
|
– Cisco IOS XE Software Release 16.12.1 with AP Device Pack, or later |
| Supported wireless LAN controllers |
– Cisco Catalyst 9800 Series Wireless Controllers |
|
– Cisco 3504, 5520, and 8540 Wireless Controllers and Cisco Virtual Wireless Controller |
| 802.11n capabilities |
– 4×4 MIMO with four spatial streams |
|
– Maximal Ratio Combining (MRC) |
|
– 802.11n and 802.11a/g |
|
– 20- and 40-MHz channels |
|
– PHY data rates up to 1.5 Gbps (40 MHz with 5 GHz and 20 MHz with 2.4 GHz) |
|
– Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive) |
|
– 802.11 Dynamic Frequency Selection (DFS) |
|
– Cyclic Shift Diversity (CSD) support |
| 802.11ac capabilities |
– 8×8 downlink MU-MIMO with eight spatial streams |
|
– MRC |
|
– 802.11ac beamforming |
|
– 20-, 40-, 80-, and 160-MHz channels |
|
– PHY data rates up to 6.9 Gbps (160 MHz with 5 GHz) |
|
– Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive) |
|
– 802.11 DFS |
|
– CSD support |
|
– WPA3 support |
| 802.11ax capabilities |
– 8×8 uplink/downlink MU-MIMO with eight spatial streams |
|
– Uplink/downlink OFDMA |
|
– TWT |
|
– BSS coloring |
|
– MRC |
|
– 802.11ax beamforming |
|
– 20-, 40-, 80-, and 160-MHz channels |
|
– PHY data rates up to 10 Gbps (160 MHz with 5 GHz and 20 MHz with 2.4 GHz) |
|
– Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive) |
|
– 802.11 DFS |
|
– CSD support |
|
– WPA3 support |
| Integrated antenna |
– 2.4 GHz: Peak gain 4 dBi, internal antenna, omnidirectional in azimuth |
|
– 5 GHz: Peak gain 6 dBi, internal antenna, omnidirectional in azimuth |
| External antenna with Smart antenna connector |
– Cisco Catalyst 9130AXE Access Point is certified for use with antenna gains up to 13 dBi (2.4 GHz and 5 GHz) |
|
– Supports Self-Identifiable Antennas (SIA) on the Smart antenna connector |
|
– Smart antenna connector is a compact multi-RF connector with 8-DART interface |
|
– Requires the AIR-CAB002-D8-R= 2-fppt smart antenna connector when used with antennas with an RP-TNC connector |
|
– Requires the AIR-CAB003-D8-N= 3 ft smart antenna connector when used with AIR-ANT2513P4M-N= antenna |
| Interfaces |
– 1x 100, 1000, 2500, 5000 Multigigabit Ethernet (RJ-45) – IEEE 802.3bz |
|
– Management console port (RJ-45) |
|
– USB 2.0 at 4.5W (enabled via future software) |
| Indicators |
– Status LED indicates boot loader status, association status, operating status, boot loader warnings, and boot loader errors |
| Dimensions (W x L x H) |
– Access point (without mounting brackets): C9130AXI: 8.9 x 8.9 x 1.88 in. (22.6 x 22.6 x 4.8 cm) |
| Environmental |
– Nonoperating (storage) temperature: -22° to 158°F (-30° to 70°C) |
|
– Nonoperating (storage) altitude test: 25˚C, 15,000 ft (4600 m) |
|
– Operating temperature: 32° to 122°F (0° to 50°C) |
|
– Operating humidity: 10% to 90% (noncondensing) |
|
– Operating altitude test: 40˚C, 9843 ft (3000 m) |
|
– Note: When the ambient operating temperature exceeds 40°C, the access point will shift from 8×8 to 4×4 on the 5 GHz radio, and uplink Ethernet will downgrade to 1 Gigabit Ethernet; however, the USB interface will remain enabled. |
| System memory |
– 2048 MB DRAM |
|
– 1024 MB flash |
| Warranty |
– Limited lifetime hardware warranty |
| Available transmit power settings |
– See detailed power settings for both 2.4 GHz and 5 GHz frequencies |
| Maximum number of nonoverlapping channels |
– See specified numbers for 2.4 GHz and 5 GHz frequencies |
| Compliance standards |
– Refer to the provided list of safety, emissions, immunity, RF safety, and IEEE standards |
